#16528
SKRIPSI/JUR.TM.PS.PRODUKSI DAN PERAWATAN 057 FAJ r 2022 ISBN:18 641 015
Subjects:Teknik mesin Penelitian
RANCANG BANGUN PELEPASAN DAN PEMASANGAN BEAERING JOINT BERBASIS SISTEM HIDROLIK --
FAJAR YOGA WARDANA / / /SAMARINDA 2022
Viii; 175 h; ilus; 23 cm Bahasa:IND
ABSTRAK
Fajar, ‘Rancang Bangun Alat Pelepasan dan Pemasangan Bearing Joint Berbasis Sistem
Hidrolik’, dibawah bimbingan Ir. Markus Tato Mangando M.T., dan Ir. Sudirman Ali,
M.Si., Laporan Tugas Akhir, Program Studi S1 Terapan Produksi dan Perawatan Mesin,
Jurusan Teknik Mesin, Politeknik Negeri Samarinda.
Pada saat ini banyak perkembangan teknologi yang sudah banyak membantu manusia
untuk memperoleh setiap pekerjaan dan mempercepat pekerjaan sehingga lebih efisien
dalam segi waktu dan pekerjaan dengan menghasilkan kreasi yang bertujuan untuk
memudahkan pekerjaan manusia. Oleh karena itu penulis berinovasi dengan menciptakan
alat pelepasan dan pemasangan bearing joint dengan prinsip kerja sistem hidrolik yaitu
suatu bentuk perubahan atau pemindahan daya dengan menggunakan media penghantar
berupa fluida cair untuk memperoleh daya yang lebih besar dari daya awal yang
dikeluarkan.
Perencanaan ini bertujuan untuk membuat alat pelepasan dan pemasangan bearing joint
berbasis sistem hidrolik yang digunakan untuk memasang dan melepas bearing Joint.
Sistem hidrolik dengan penggerak mula power pack daya motor listrik 2 HP dengan
putaran 1400 rpm menghasilkan debit pompa 5 Liter/menit. Untuk pelepasan bearing
dengan pressure gauge (P) sebesar 0,34 N/mm2
didapat gaya angkat sebesar 225,20 N
dengan berat 22,98 kg. Untuk pemasangan bearing dengan pressure gauge (P) sebesar
0,71 N/mm2
didapat gaya angkat sebesar 470,26 N dengan berat sebesar 47,99 kg. Alat
ini pun menghasilkan beban tarik aman sambungan baut dan mur sebesar 464 kg dan juga
beban yang dapat ditahan oleh hasil pengelasan pada sambungan rangka (12 titik las)
sebesar 451,5 kg.
Kata kunci : Pressure Gauge, Sistem Hidrolik, Tracker Bearing.
viii
ABSTRACT
Fajar, 'Design and Build a Hydraulic System-Based Bearing Joint Removal and
Installation Tool', under the guidance of Ir. Markus Tato Mangando M.T., and Ir.
Sudirman Ali, M.Si., Final Project Report, Applied S1 Study Program in Mechanical
Production and Maintenance, Department of Mechanical Engineering, Samarinda State
Polytechnic. At this time, there are many technological developments that have helped
humans to obtain every job and speed up work so that it is more efficient in terms of time
and work by producing creations that aim to facilitate human work. Therefore, the author
innovates by creating a bearing joint removal and installation tool with the working
principle of the hydraulic system, which is a form of power change or transfer by using a
conducting medium in the form of liquid fluid to obtain power greater than the initial
power released.
This planning aims to make a hydraulic system-based bearing joint removal and
installation tool used to install and remove the bearing joint. Hydraulic system with a
power pack drive of 2 HP electric motor power with a revolution of 1400 rpm produces
a pump discharge of 5 liters / minute. For the release of bearings with a pressure gauge
(P) of 0.34 N / mm2, a lifting force of 225.20 N with a weight of 22.98 kg was obtained.
For the installation of bearings with a pressure gauge (P) of 0.71 N / mm2, a lifting force
of 470.26 N with a weight of 47.99 kg was obtained. This tool also produces a safe tensile
load of bolt and nut joints of 464 kg and also a load that can be withstanded by welding
results at the frame joint (12 welding points) of 451.5 kg.
Keywords : Pressure Gauge, Hydraulic System, Tracker Bearing