#16490
SKRIPSI/JUR.TM.PS.PRODUKSI DAN PERAWATAN 012 HER r 2022 ISBN:18 641 100
Subjects:Teknik mesin Penelitian
RANCANG BANGUN MESIN PEMBERI PAKAN IKAN OTOMATIS DENGAN TENAGA SURYA --
HERIK TODING BUA / / /SAMARINDA 2022
Viii; 175 h; ilus; 23 cm Bahasa:IND
ABSTRAK
Pemberian pakan ikan yang tidak teratur adalah permasalahan yang sering
terjadi pada pembudidayaan ikan sehingga pertumbuhan ikan tidak maksimal.
Solusi supaya pemberian makan ikan menjadi teratur maka diperlakukan
pembagian waktu selama 24 jam dan letak tempat pemberian makan ikan. Dengan
memanfaatkan teknologi elektronika yaitu dengan merancangkan sebuah alat
pemberi makan ikan otomatis yang dapat di buat dengan memanfaatkan RTC (real
time clock). RTC dapat digunakan untuk mengatur waktu pemberian makan ikan,
Sebuah Arduino Uno digunkan sebagai pengendali sistem kontrol secara
keseluruhan. Arduino Uno berfungsi sebagai mengolah sinyal input. Output dari
Arduino Uno adalah motor servo. Sebagai sumber energi untuk alat pemberi
makan ikan otomatis maka dipergunakan pembangkit listrik tenaga surya 50 Wp
(Watt Peak) dan menyimpan daya ke aki. Untuk menstabilkan tegangan dari solar
sel dibutuhkan SCC (Solar Charger Controller). Motor servo berfungsi untuk
membuka dan menutup katup makanan ikan.Berdasarkan hasil perancangan dan
pembuatan yang telah diuraikan sehingga didapat data sebagai berikut: a. Motor
DC - Daya : 7,6 Watt - Torsi : 0,223 N.m - Speed : 6.000 rpm b. Poros - Bahan
Poros : S 30C - Diameter Poros : 10 mm - Panjang Poros : 180 mm c. Bantalan -
Jenis Bantalan : 6200ZZ - Diameter Luar Bantalan : 26 mm - Diameter Dalam
Bantalan : 10 mm - Umur Bantalan : 124.613,98 jam.
Kata kunci : Mesin pemberi pakan ikan, Rel Time Clock (RTC), Arduino Uno
iv
Abstract
Irregular feeding of fish is a problem that often occurs in fish farming so
that fish growth is not optimal. The solution so that the feeding of the fish becomes
regular, then the time division is treated for 24 hours and the location of the fish
feeding place. By utilizing electronic technology, namely by designing an
automatic fish feeding device that can be made using RTC (real time clock). RTC
can be used to set the feeding time of fish, An Arduino Uno is used to control the
overall control system. Arduino Uno functions as a processing input signal. The
output of the Arduino Uno is a servo motor. As an energy source for the automatic
fish feeder, a 50 Wp (Watt Peak) solar power plant is used and saves power to the
battery. To stabilize the voltage from the solar cell, SCC (Solar Charger
Controller) is needed. The servo motor functions to open and close the fish food
valve. Based on the results of the design and manufacture that have been
described, the following data are obtained: a. DC Motor - Power : 7.6 Watt -
Torque : 0.223 N.m - Speed : 6.000 rpm b. Shaft - Shaft Material : S 30C - Shaft
Diameter : 10 mm - Shaft Length : 180 mm c. Bearing - Bearing Type : 6200ZZ -
Bearing Outer Diameter : 26 mm - Bearing Inner Diameter : 10 mm - Bearing
Life : 124.613.98 hours.
Keywords : Fish feeding machine, Rail Time Clock (RTC), Arduino Uno