#11849
SKRIPSI/TE 024 MAG a 2019 ISBN:15642021
Subjects:Teknik Elektro Teknik Elektro
ANALISIS PENGARUH PERUBAHAN TEGANGAN TERHADAP KARAKTERISTIK MOTOR INDUKSI GM-1-03C --Ed.1
MAGHFIRAH / / /POLNES Samarinda 2019
xix; 66 hlm.; 29x21cm; CD Bahasa:Ind
ABSTRAK
Maghfirah Pembimbing:
15 642 021 I. Ir. H. Masing, M.T.
Program Studi Teknik Listrik D-IV II. Rusdiansyah, ST., M.T.
Analisis pengaruh Perubahan Tegangan Terhadap Karakteristik Motor Induksi GM-1-03C
Abstrak, PT Pertamina RU V Balikpapan menggunakan komponen kelistrikan yang menunjang
proses produksi salah satunya Motor Induksi GM-1-03 C dengan kapasitas 850 kW/6.6kV yang
merupakan motor induksi tiga fasa yang berperan sebagai motor pompa untuk mengalirkan fluida
dari desalter tank C-1-08 menuju ke furnace F-1-01 A/B. Penelitian ini membahas mengenai
pengaruh perubahan tegangan terhadap karakteristik motor induksi GM-1-03C. Analisis dalam
penelitian ini menggunakan software ETAP 12.6 dengan metode analisisnya menggunakan
Metode Newton-Rhapson. ETAP 12.6 digunakan untuk membantu mengetahui hubungan antara
perubahan tegangan terhadap kecepatan, perubahan tegangan terhadap torsi dan perubahan
kecepatan terhadap torsi dalam bentuk grafik. Berdasarkan hasil simulasi dan analisis diperoleh
hasil: Perubahan tegangan sumber dapat menyebabkan perubahan unjuk kerja pada motor
diantaranya: perubahan arus, perubahan kecepatan, dan perubahan nilai torsi. Akibat terjadinya
perubahan kecepatan putar pada motor maka menyebabkan nilai torsi ikut berubah, artinya jika
putaran rotor dipercepat, maka torsi yang dihasilkan kecil, sedangkan jika torsinya besar maka
kecepatannya lambat. Perubahan tegangan seperti kenaikan tegangan dapat disebabkan oleh
lepasnya beban secara tiba-tiba, sedangkan penurunan tegangan dapat disebabkan oleh kecepatan
torsi, dimana semakin cepat putaran torsi maka nilai arus semakin naik dan menyebabkan
tegangan semakin turun.
Kata Kunci: Motor induksi, tegangan, kecepatan, torsi, ETAP 12.6, pompa.
viii
ABSTRACT
Maghfirah Pembimbing:
15 642 021 I. Ir. H. Masing, M.T.
Program Studi Teknik Listrik D-IV II. Rusdiansyah, ST., M.T.
Analysis of the Effect of Voltage Changes in the Characteristics of GM-1-03C Induction
Motors
Abstract, PT Pertamina RU V Balikpapan uses electricity components that support the production
process, one of which is the GM-1-03 C Induction Motor with a capacity of 850 kW / 6.6kV which
is a three-phase induction motor that acts as a pump motor to flow fluid from the desalter tank C-
1-08 head to the F-1-01 A / B furnace. This study discusses the effect of voltage changes on the
characteristics of GM-1-03C induction motors. The analysis in this study uses ETAP 12.6 software
with the method of analysis using the Newton-Raphson Method. ETAP 12.6 is used to help
determine the relationship between voltage changes with speed, voltage changes with torque and
changes in speed with torque in graphical form. Based on the results of simulation and analysis
obtained results: Changes in source voltage can cause changes in the performance of the motor
including changes in current, changes in speed, and changes in torque value. Due to changes in
rotational speed on the motor causes the torque value to change, meaning that if the rotor rotation
is accelerated, the torque produced is small, whereas if the torque is large then the speed is slow.
Voltage changes such as an increase in voltage can be caused by a sudden release of load, whereas
a decrease in voltage can be caused by torque velocity, where the faster the torque turns, the
current value rises and causes the voltage to decrease.
Keywords: Induction motor, voltage, speed, torque, ETAP 12.6, pump.